Smart Camera 2.0 Quick Start Guide

When setting up the Smart Camera with your 3 Point Wireless Network, it is strongly recommended to set up in this sequence:

1. Set all Pressbox equipment up first
2. Set up all Endzone equipment but DON'T raise the tower yet
3. Set up all Sideline equipment and temporarily test the system at this location
4. Once it is confirmed everything is working raise the endzone tower
5. Lastly bring the iPad back up to the pressbox where you will connect to the Pressbox wifi and control the system from this location.

This method avoids most errors and reduces the amount of walking across the field.

Pressbox Equipment Setup

Step 1: Power up the Pressbox Kit and connect Pressbox Bridge antenna

MAKE SURE THE BRIDGE HAS A CLEAR SHOT OF WHERE THE OTHER BRIDGES WILL BE SET UP FREE OF OBSTRUCTIONS.

Step 2: Set the Pressbox iPad Antenna on Window INSIDE OF ROOM with iPads

Take the iPad antenna and use the suction cup on the back to stick it to a window in the press box and position towards the coaches inside. The "rabbit ears" ideally should each be at a 45-degree angle.

The antennas and optional EDGE box should be connected to the Press Box Kit router like this:

Step 3: Setup your Pressbox Sony Camera

Connect the HDMI cable from your pressbox camera to the Connect Camera port of the EDGE box:

Make sure that your camera HDMI resolution setting is on "Auto" if it's a Sony camera, or "720p" and that Power Save is OFF.

Endzone Tower Setup

30' Tower Setup

Insert the tower into the base plate with wheels and then extend all 4 locking legs:

Then tighten all 4 knobs:

DON'T RAISE THE TOWER YET!

20' Tower Setup

Loosen the top mast knob and start spreading the three legs. It's easiest to anchor one leg against the ground and pull apart:

Expand the legs as wide as possible and then loosen the lower mast knob:

Lower the center mast pole to the ground and then re-tighten the lower knob:

Lastly, tighten the upper mast knob:

DON'T RAISE THE TOWER YET!

Endzone Equipment Setup

Equipment Overview - Endzone Kit:

Step 1. Mount the camera head onto the tower.

Be sure to push all the way down. BOTH O-Rings should be fully inserted.

 

Step 2. Connect the 30-foot Ethernet Cable key ring to the carabiner already attached to eyelet screw

Retrieve your 30ft cable from inside your tower bag

Note: This cable is NOT in the hardcase along with the rest of the equipment, it is in the tower bag. Be sure to look for it thoroughly, we promise we've included it!

Step 3: Connect the Ethernet Cable to the Wireless Head

Connect the Ethernet cable into the port in the bottom of the Pan/Tilt head. Make sure that there is a large loop on the Ethernet cable to ensure the weight of the cable is on the relief hook, and not on the Ethernet port, as shown below.

 

Step 4: Turn your Battery On and tap AC

Step 5: Plug In All Cables as shown

Step 6: Attach the Bridge Antenna to the Tower

Make sure to angle the Bridge Antenna directly toward the Pressbox Bridge antenna.

Sideline Equipment Setup

Step 1: Set up on 20-25 YL and Attach the Antennas to their tripod

Using the provided clamp mounts and/or velcro or zip tie, attach your antennas to your tripod as shown below: 

Prior to 2025, you will have a 2-part iPad antenna with rectangular Booster panel in addition to the round Bridge:

Note: You will need to connect the booster panel to the iPad antenna. Simply screw the 2 cables on the base of the booster panel onto the threaded tips of the iPad antenna

Step 2: Connect the antennas to the router and POE injector

(1) Connect the round Sideline Bridge antenna directly into the Switch in the black labeled port: Bridge Antenna (2) The iPad Antenna must plug into the POE injector in the black labeled port: iPad Antenna. As shown below:

If you have the 2-Part iPad Antenna with Booster Panel simply connect the black Ethernet cables from both antennas into the sideline router, into the ports labeled "Antenna."

Turn on the battery:

Make sure to angle the Bridge Antenna directly toward the Pressbox Bridge antenna and the iPad Antenna booster panel should be angled towards the sideline where the coaches' iPads will be roaming:

Step 3: Verify

Once this is complete, connect your iPad to the Sport Scope Sideline network. Open the menu on the left and tap on Cameras to check the status of the cameras. Verify that you can see both the Pressbox and Endzone camera:

Next we will create a test game to temporarily test the Smart Endzone Camera on the field to make sure everything is working:

• If you do not know how to create a new game yet, go to: How To Create and Start a Game.

Once the game is created:

1. Verify the endzone live video feed is on and the pressbox angle Ready status is in the top left corner. 

1.  
   • YOU WILL NOT SEE LIVE VIDEO FOR THE PRESSBOX ANGLE. THIS IS NORMAL AND CORRECT.
   • If the endzone angle is in the top left corner tap on it to switch angles.
2. Test the motor controls (by default on the right hand of the screen).
3. Test the zoom controls (by default left side of screen).
4. Record a few test clips using the red record button.
   • Tap the thumbnail of the clip you recorded at the bottom of the screen and if you have two angles make sure you can watch the replay for both angles. 

Assuming everything is working, the best practice is to turn off the Wifi from the iPad settings and now head back to the Endzone to raise the tower.

Raising the Tower

1. Loosen top knob and slide pole up.
2. Once you feel the stopper, slide the pole down a few inches.
3. Lock the knob and clip the blue ethernet cable into the large carabiner.
4. Repeat with each pole to reach desired height.

IMPORTANT! - Always keep two hands on tower poles when raising or lowering for safety.

Return to Pressbox to Control the System with the Master iPad

Once complete, walk back up to the pressbox and connect to the SportScopePressbox Wi-Fi to finally control the system for your game. You may create another new Game.

• All Coach Replay viewing iPads will connect to their respective Wi-Fi signal depending on where the iPad is located and then go the Game that the control iPad has created in order to view the instant replay play clips.

Congratulations, the setup is now complete!